REAL RESULTS

Before & After Window Tinting

See the difference professional ceramic window tint makes on real vehicles from our Greenville shop. Every install uses XPEL, LLumar, or 3M ceramic film.

⚡ Quick Answer

Window tint transforms the look and comfort of any vehicle. Below you’ll see real before-and-after examples from sedans, trucks, and SUVs — each with the film brand, shade percentage, and VLT noted so you know exactly what you’re looking at.

Sedan — XPEL XR Plus 20% All Around

This 2024 Honda Accord came in with no tint. The owner commutes on I-85 between Greer and downtown Greenville and wanted maximum heat rejection without going too dark. We installed XPEL XR Plus at 20% on the rear and side windows, with a 35% ceramic strip on the windshield to stay within SC law (§ 56-5-5015 requires 27% VLT on front windows).

Before: Factory glass with no tint. Full sun exposure, hot interior, zero privacy. The cabin was reaching 140°F+ when parked on Woodruff Road during summer.

After: Clean, uniform look with consistent shade all around. Interior temperature dropped 15–20°F on hot days. UV exposure cut by 99%, protecting leather seats from cracking and fading. The owner reported his AC catches up in half the time.

Does 20% tint look too dark on a sedan?

It depends on the car’s color. On lighter-colored vehicles (white, silver, light gray), 20% gives a sleek contrast without looking aggressive. On dark-colored cars (black, dark blue, dark gray), 20% can appear very dark from the outside but still offers good visibility from inside during the day. At night, you’ll notice reduced visibility in parking lots — most drivers adjust within a week.

Truck — LLumar CTX 15% Rear / 35% Front

A 2023 Ford F-150 that works as a daily driver and weekend hauler. The owner wanted the darkest legal setup for privacy when tools and equipment are in the back seat. We installed LLumar CTX at 15% on the rear and back side windows, with 35% on the front sides to comfortably clear the 27% VLT requirement after meter testing.

Before: Factory privacy glass on the rear (about 20% VLT from the factory), clear glass on the front sides. Mismatched look with no heat protection on the front.

After: Uniform appearance from front to back. The LLumar CTX ceramic blocks 80% of infrared heat even at the lighter 35% shade on the front windows. No more arm burn on the driver’s side during afternoon drives down Pleasantburg Drive.

Can you tint over factory privacy glass?

Yes. Factory privacy glass is typically dyed glass at about 15–20% VLT. Adding ceramic tint over it brings the combined VLT down further (15% film over 20% factory glass gives roughly 3–5% VLT), which is very dark but perfectly legal on rear windows in South Carolina. The real benefit is heat rejection — factory privacy glass blocks almost no infrared heat, while ceramic film blocks 80–98%.

SUV — 3M Ceramic IR 30% Full Package

A 2024 Toyota 4Runner driven by a family with two young kids. They wanted glare reduction for car seats, UV protection, and a subtle look that doesn’t scream “blacked out.” We installed 3M Ceramic IR at 30% all around with a 50% windshield strip.

Before: Completely clear glass. Kids were squinting and overheating in the back seat, especially on afternoon pickups from school in Five Forks.

After: Comfortable cabin without the fishbowl feel. The 30% shade lets enough light through that the interior doesn’t feel cave-like, but cuts enough glare that the kids can nap without sun blasting through. 3M Ceramic IR blocks 95% of infrared heat and 99.9% of UV, protecting both skin and the leather interior.

What to Expect From Your Install

Every tint job at our Greenville shop follows the same process. We clean the glass inside and out, cut the film to your vehicle’s exact window pattern using a digital plotter (not freehand), apply it with a slip solution, squeegee out all moisture, and inspect every edge under bright light. The whole process takes 2–4 hours depending on the vehicle.

After installation, you’ll see small water bubbles or a slightly hazy appearance — that’s normal. The film needs 3–7 days to fully cure in warm weather (up to 2–3 weeks in winter). Don’t roll your windows down for at least 48 hours after install. Once cured, the tint will look crystal clear with no bubbles, haze, or imperfections.

How long does window tint last before it needs replacing?

Ceramic film from XPEL, LLumar, and 3M lasts 10–15+ years with no fading, bubbling, or peeling. That’s the advantage of ceramic over dyed film — it doesn’t degrade under UV exposure the way dyed films do. All three brands carry lifetime warranties that cover defects. The only reason you’d replace ceramic tint is if the window itself gets damaged or you want a different shade.

What Customers Say

★★★★★

“The before and after on my Camry was night and day. Went from a greenhouse to a comfortable ride. My wife saw mine and booked her Highlander the same week.”

— Daniel M., Greenville

★★★★★

“I was nervous about going dark on my white Tesla. They showed me samples first and nailed the shade I wanted. It looks factory and the heat rejection is no joke — my range actually improved because I’m using less AC.”

— Sarah K., Simpsonville

★★★★★

“Third vehicle I’ve had tinted here. My Silverado, my wife’s Equinox, and now my son’s Civic. Consistent quality every time. The before-and-after difference never gets old.”

— Marcus T., Taylors

Before & After FAQ

Can I see tint samples before choosing a shade?
Yes. We keep sample strips of every shade for all three film brands. We can hold them up to your car’s windows so you see exactly how each shade looks on your specific vehicle and glass color before committing. We also have a heat lamp so you can feel the infrared rejection difference between film types.
Will the tint look the same on my car as the photos?
The same shade percentage can look different depending on your car’s glass color, paint color, and whether you have factory privacy glass. A 20% tint on a white car looks darker from the outside than on a black car because of contrast. That’s why we always recommend seeing samples on your actual vehicle before choosing.
How soon after tinting does it look finished?
Immediately after installation, you may notice small water pockets or a slight haziness — this is completely normal and part of the curing process. In warm weather (above 70°F), the film typically cures in 3–7 days. In cooler months, it can take 2–3 weeks. Once cured, the tint looks crystal clear with a uniform finish.
Do you photograph every job?
We photograph most installs for our portfolio with the customer’s permission. If you’d prefer your vehicle not be photographed, just let us know — no pressure at all. We also keep installation records with the film brand, shade, and date for warranty purposes.

Ready to Transform Your Vehicle?

See the difference ceramic tint makes on your car, truck, or SUV. Free quotes, same-week appointments available at our Greenville shop on Pleasantburg Drive.